Tag Archives: PVC

PVC Stand for 4’9″ Doll for Child Passenger Safety

20 Feb

I actually made this a few months ago, but am just now getting around to sharing it!

After completing a few PVC pipe projects, I am always looking for other creative ways to use it. We have a 4’9″ demonstration doll for our Child Passenger Safety Technician classes, and I like to take it to check events and informational booths we set up to have a visual idea of what 4’9″ really is. This poor guy has been bungie-strapped to many poles, posts, easy-up sides, and usually slumps down pretty early on in our events.

So, I came up with the idea of making a stand for the doll using PVC pipe. At first, I just had a straight stand, but then decided to add the bar off to the side to make it like the height requirement bars for rides at amusement parks. The bottom of the bar is 4’9″, so kids can walk up to it and see if they are as tall as the bar.

Of course, being 8 years old or 4’9″ isn’t the magic age or height to stop using a booster seat, so I also included the 5 Step Test from Safety Belt Safe USA.

So, here is what the sign says:

Your child must be at least
to use just the seat belt.
Or, they need to pass the 5-Step Test.
The 5-Step Test
Does the child sit all the way back against the auto seat?
2. Do the child’s knees bend comfortably at the edge of the auto seat?
3. Does the belt cross the shoulder between the neck and arm?
4. Is the lap belt as low as possible, touching the thighs?
5. Can the child stay seated like this for the whole trip?
If not, use a booster seat to give them a boost!

He still slumps down a little bit, but it holds him up better than a bungie-strap!

All PVC is 3/4″ diameter. Need 14.5 feet of PVC pipe, 3 caps, 5 tees, and 5 elbows to complete.
Base: 2 10″ pieces, 4 3-1/2″ pieces, 2 tee fittings, 4 elbows
Then, 2 43″ pieces into 2 tee fittings
Arm props: 2 6″ pieces with caps on the end
Then, 2 11″ pieces, one goes into elbow, one goes into tee fitting
10″ piece across top, 10″ piece out the side with a cap on the end

Stand for 4'9" Doll

All the dolls at a seat check event

PVC Bike and Kid Wash

20 Nov

It’s been a while since I made this, but I wanted to make sure to still share it.  After making the PVC bike rack, which has been awesome to have in the garage to keep the bikes organized, I wanted to make something else.  A friend of mine had found this project, a Kid’s Car Wash Sprinkler, on the Lowe’s website.  After looking over the plans, I made a few changes to use a little less PVC pipe and to not make it quite as big for storage purposes.

bike wash plans


Now, from my original plans, I was not able to locate a grass skirt, so I improvised and used a folded and cut disposable tablecloth from the dollar store.  Here is a picture of how it turned out:

Completed Bike Wash


The kids really enjoyed it!  My water feature part wasn’t quite perfect.  I don’t think the front section got completely sealed off, so water was flowing throughout the entire system instead of just the section with the holes drilled in.  That made the water pressure a little low, but, it was still enough to get the kids wet!  The hose I got was just long enough to make it to my sidewalk, thankfully.  I only used PVC cement in the section for the water, so the rest can come apart and go back together for storage or transport.

Since it does come apart, now that it’s cooled off and too cold to get soaking wet, I made a slight modification for the current weather:

Bubble wash


I removed the water section, and just used the part with the tablecloth and sponges.  Then, I put our bubble machine in front to have bubbles in place of the water.  This way, we get use out of it more of the year, even in the more mild weather in AZ.

I overbought on PVC pipe on this last project, so I have some in my garage, just waiting for the next project.  Let’s see what I can make next!

Note: Prices of supplies may vary by where you decide to shop.  I provided the prices just as a rough estimate for the project cost.

DIY PVC Bike Rack

13 May

I was tired of the bike and scooter mess in my third garage.  I had been shopping around to see if there was any kind of small bike rack I could use in my garage, but they were a little out of my price range.  So, I searched on the internet some, and came across a few plans to make a bike rack out of PVC pipe.  I recently used PVC pipe for a sign project for Bountiful Baskets, and it was really easy to work with, so I decided to give it a try.

I used these sites to help with my plans: Project #4 – DIY Bike Rack Made from PVC Pipe, Make your own Bike Rack, and PVC Bike Rack

My supplies that I purchased at Lowe’s:

40′ of 3/4″ Schedule 40 PVC pipe, cost $8.12 for 4 10′ sections of pipe
34 Tees, cost $8.74 for 3 10 count bags and 4 single tees
6 90 degree elbows, cost $1.86

Total = $18.72, plus tax

You may opt to use PVC cement to hold it together, but I did not use any at this point.  It is staying together well, plus, I want the option to adjust, add, or take away as we get new scooters or bikes.

You also will need a way to cut the pipe.  There is a pipe cutting tool available, shown below.  This one was $9.97 at Lowe’s.  I bought it, but will probably return it since I was able to use my tree cutting tool, also shown below, with success.  You can also use a small hacksaw to cut the pipe.

How you cut your pipe will depend how many items you want to store, and on the size your bike tires and scooters.  For the scooters, I made it wide enough so most of the scooter could fit in.  For the bikes, they have 2″ wide tires, so I cut the pipe to have a 2″ wide section in those parts.  Here is a picture with my dimensions:

I ended up with the following:

20 8″ sections
10 12″ sections
12 10″ sections
3 5″ sections
6 3.5″ sections
6 1.5″ sections’

If you decide to use 1″ PVC pipe instead of 3/4″ PVC pipe, you may need to adjust the measurements slightly, and the cost will be a little higher, but shouldn’t be too much more.

This was a really fun project for me.  It took a little trial and error to get the openings the right size, but after that, it went pretty smoothly.  This turned out to be the perfect size for the opening of my third garage, so we can easily open up the garage and get the bikes and scooters out right away.  I also made sure to get my kids involved.  My older daughter counted out the number of tees and elbows from the plans I drew up, then both my daughters helped me count out the items we needed at the store.  I did all the cutting, but they were able to help with the assembly.  I have found some other neat PVC ideas online, so we may be doing more projects like this in the future!

%d bloggers like this: